Complete Pump Supplies | Supplier Domestic Water Pumps & Booster Pumps

Compact 600 2V.­600.­311S.­0904 Twin Pump Space Saving Booster Set & Tank

Compact 600 2V.600.311S.0904 Twin Pump Space Saving Booster Set & Tank

Flowpac Compact

  • Flowpac Compact
  • Flowpac Compact (Space Saving Booster Set)
  • IMG_20150130_113847945
Product code: 2V.­600.­311S.­0904
£5800.00
£6960.00 inc. VAT
Ship to:

Description

Compact 600 2V.­600.­311S.­0904 Twin Pump Space Saving Booster Set & Tank

The Compact 600 Booster Set offers space saving solutions for boosting water where the mains pressure is inadequate. The Compact Booster Sets are designed to supply potable (drinking) water to domestic and commercial premises.

This Booster Set is almost silent running less than 45dba and is a space saving and high effciency solution variable speed stainless steel submersible pump.

The Compact Booster Sets are available in eight standard sizes (from 600L - 3001L). This is with single and twin pump options. All the Compact Booster Sets are designed to meet the requirements of the water regulations.

This Booster Set is available with AG Air Gap for portable applications and AB Air Gap for CAT5 applications.

Controller

The Compact Booster Sets comes complete with a variable speed drive(s) controls with digital system display, these are mounted on the top of the tank, this allows for easy maintenance. The Booster Sets display gives a simple and clear system overview, this includes pressure, speed, frequency and power absorbed. The Flowmat controller also offers automatic changeover of duty pump, volt free contacts, BMS remote alarm connections and provision for wiring of low level float switch as standard.

GRP Cold Water Storage Tank

The GRP cold water storage tank is insulated to keep the noise level to a minimum. Low maintenance and long lasting our GRP one piece cold water storage tanks are specifically designed and tested to ensure that they meet the requirements set by BS EN 13280:2001. they also have full WRAS approval giving you complete peace of mind. These are available in AG, AA and AB (CAT 5) airgap configurations.

  • Fully encapsulated insulation to sides and lid.
  • A close fittting and sealed lid which removes for maintenance.
  • CFC free PU foam insulation, which is completely enscapsulated within the GRP laminate.

Standard Features

  • GRP insulated water storage tank (WRAS Approved)
  • 600L - 3001L (other sizes are available upon request)
  • Low water level pump protection (as standard)
  • Common alarm volt free contactors
  • Max head Up to 7.5 Bar
  • Max Flow Up to 166L/Min
  • 2 Year Guarantee

General Information

This information is to assist in the installation of the cold water booster set, please make sure to follow them carefully, if you are unsure about any aspect of the installation feel free to call our office on 0808 168 6767. Do not lift the booster by the pipe work or by the control panel. The Anti Cycle Vessels are supplied loose for transport purposes, please ensure that the booster set has been put in to place and connected to the suction and discharge pipe work before installing the Anti Cycle Vessels, on no account should the Anti Cycle Vessels be used to “manouvre” the booster set in to place.

Siting/­Installing the Booster Set

  • The Booster Set must be installed within an area where in the event of any component or pipework failure the resultant water leak won't cause any damage to surrounding property, if the Booster Set is to be installed or stored prior to installation in an unheated room then adequate frost protection must be added, the maximum ambient temperature should not exceed 35oc.
  • The Booster Set must be installed on a level surface and if the plant room has a chance of flooding it is recommended that the Booster Set is elevated and installed on a suitable plinth.
  • If the optional anti vibration mounts have been purchased then fix these to the floor/plinth then fix the booster set to the a.v mounts.
  • Care must be taken to ensure the booster set has a flooded suction from the cold water storage tank unless specific self priming pumps have been specified.
  • A full bore isolating valve must be installed on the discharge to enable commissioning and maintenance to be carried out correctly.
  • The pumps are suitable for a water temperature between 0oC and 35oC and a maximum pressure of 8.0 bar
  • Before switching on the booster set please ensure the pumps have been adequately primed.
  • An Anti Cycle Vessel (or several, depending on the model) will be supplied to eliminate hunting of the pumps; additional units can be installed next to the Booster Set if required. An Anti Cycle Vessel MUST always be fitted on the discharge manifold, do not attempt to operate the Booster Set without first installing the anti cycle vessel/s as serious damage to the Booster Set can occur.
  • The vessel air charge should be maintained at 0.3 bar below the systems nominal operating pressure.e.g.
  • Nominal System Pressure = 3.0 bar
  • Anti Cycle Vessel Air Pressure = 2.7 bar

 


Video

  

Reviews

There are no reviews yet.

Add review

Name:
Email:
Rating:
  • Overall satisfaction
  • Quality
  • Value for money
  • Performance
  • Ease of use
Comment:
Spam protection:
U7KBWQ9XJC3DTR

Type or copy & paste the code you see on the left side.

Delivery

Delivery Information

Free delivery relates to MOST products on the Website over the value of £100.00 (excluding VAT). 

*Unless otherwise stated on individual items* 

Products purchased under £100.00 will incur a £6.95 delivery charge.

Standard Delivery Orders over £100.00 (3-5 working days)* - Free shipping for in stock items to mainland UK*. 

Next day shipping is only available for stock items which are ordered before 14:00 at a charge of £12.50*. Any orders that are placed after this time will be processed the following day.

Specified delivery times are based on orders placed before 2pm Monday to Friday (excludes Weekends and Bank Holidays)  - for more details please see "UK Shipping Charges" below.

Weekend or orders placed on a Bank holiday will be dispatched on the next working day.

*Excludes UK Islands, Republic of Ireland and Scottish Highlands.

During Christmas and New Year our warehouse will be closed. Orders over this period will be dispatched on the first working day after New Year.

Delivery times are subject to change if the item is out of stock with our supplier. There are products on our Website that are not stocked at our warehouse, nor with our manufacturer's UK warehouses, therefore lead times can vary. This is why we recommend you contact us prior to purchasing to check current stock levels and lead times.

If you are not available to take a delivery on the specified date, you must let us know immediately. If we attempt to deliver your order and no-one is in, a re-delivery charge may be incurred.  

As we use 3rd party delivery agents, Complete Pump Supplies are unable to guarantee that all deliveries will be the next working day. Complete Pump Supplies will not be liable for any loss of income, loss of profits, loss of markets, loss of reputation, loss of customers, loss of use, loss of an opportunity even if we had knowledge that such damages or loss might arise or for any indirect, incidental, special or consequential damages or loss howsoever arising.

Web design by Brick technology Ltd.